How Much Does It Cost To Drill A Well In Tennessee

Drilling a well costs $5,500 for an average depth of 150 feet. Most projects range between $1,500 and $12,000. Expect to pay between $15 and $30 per foot of depth, or up to $50 for difficult terrain. For shallow depths, digging may be a more affordable solution as $10 to $25 per foot.

How deep are wells in Tennessee?

— Wells are typically 50 – 200 feet deep. — Depth to salt water is generally greatest where the limestone and dolomite aquifers crop out i.e. the apex of the Nashville Dome.

How much does a well cost in Tennessee?

Well Drilling Costs By State State Average Cost Per Foot South Carolina $28 – $61 South Dakota $26 – $58 Tennessee $27 – $60 Texas $28 – $62.

Can I dig my own well in Tennessee?

The Tennessee Water Well Act of 1963 requires all persons drilling a water well to be licensed. A person installing a pump or water treatment device on a water well must also be licensed.

How deep is the average well?

Most household water wells range from 100 to 800 feet deep, but a few are over 1,000 feet deep. Well yields can be increased by fracturing the bedrock immediately around the drill hole and intercepted rock faults.

Can you drill your own well?

Drilling a well by hand is a lot of work, but it can be done with the right equipment. Whether you’re looking to drill a shallow or deep well, this skill is perfect for those seeking self-reliance. Wells are normally drilled on private land where city or rural water isn’t available.

How much does it cost to put in a drilled well?

Most well drillers also have a minimum charge, usually around 100ft minimum which at $45 per foot would be $4500. Drilling a water well is a long term investment and most people are reluctant to drill without knowing if they will find water, and if so at what depth.

How deep is the water table in TN?

varies greatly. 200 feet deep. generally greatest where the limestone and dolomite aquifers crop out i.e. the apex of the Nashville Dome.

How much is a septic tank in TN?

Tennessee Septic Tanks Tank / Capacity Length Price 1250 Gallon Septic Tank 116″ 2,136 1250 Gallon Septic Tank 116″ 2,283 1500 Gallon Septic Tank 135″ 2,611 1500 Gallon Septic Tank 135″ 2,787.

How long does drilling a well take?

How long does the well drilling process generally take? A domestic well generally takes one to three days to drill and complete.

Is well water safe in Tennessee?

Private water supplies in Tennessee are usually a groundwater well or a spring. Private water supplies are, for the most part, unregulated. How a private well is constructed is regulated, but the quality of the water coming from that well is not regulated. Water from springs is also not regulated.

Why is drilling a well so expensive?

The drilling depth to water and bedrock and the well’s diameter are the most significant cost factors. The average well is drilled 100 to 300 feet deep, while some shallow wells only go down to 25 feet to reach groundwater.

Where does my well water come from?

Most wells do not get their water from underground rivers, but instead get the water from aquifers. Aquifers are layers of rock and soil with water flowing through their small pores. New water, such as from rain or melting snow, drips down into the ground through the pores and cracks in the rocks and soil.

How far does well casing go down?

Well Casing Depth Modern drilled wells reach greater depths, with a foot or two of casing above the well, a minimum of 18 feet of casing below the surface, if the well goes through bedrock, at least 5 feet of casing within bedrock.

How Far Should a well be from the house?

Any contamination in your neighbor’s well can travel into your well. Some activities legally require more than a 50-foot zone of protection. As a general guidance, personal drinking water wells should have a minimum horizontal distance of at least 10 feet and preferably 25 feet from such boundaries.

How often should you disinfect your well?

Homeowners with private wells should have their well water tested every 3 to 5 years for some contaminants, including bacteria. If these tests turn up positive for bacteria, chlorinating the well may be a way to resolve the problem.

How many years does a water well last?

The average lifespan for a well is 30–50 years. 2. How deep is the well? Drilled wells typically go down 100 feet or more.

How deep should a well be for drinking water?

The quality of your water depends on several factors including geology and water levels. In order to allow for maximum ground filtration to remove impurities, your well depth should be at least 100 feet. As a general rule, the deeper you drill, it’s more likely that there will be minerals present.

How do I find the water table in my area?

How to Find My Water Table Call your local County Extension Office. It may have statistics for the average annual water table level in your area. Look online. Check out the website for your local Water Resources Office. Dig. This is the most reliable way to find the water table level on your land.

Can you build a well anywhere?

The simple answer to Connie’s question is yes. You probably can drill your own well on your property. You, of course, would have to contact your local building department to see if there are any regulations that must be followed.